Bold charcoal drawing of an engine bay from above showing pulleys, hoses, and chassis rails, moody gray and blue tones, mechanical atmosphere

TurboRX7

The ultimate resource for rotary engine RX-7s — factory documents, rotary engine fundamentals, and PowerFC tuning guides.

Explore Resources
Rotary Basics

Covers the 13B 2‑rotor and 20B 3‑rotor engines — both production and racing variants. Includes a GT35R single turbo build image gallery, various rotary engine photos, and wideband datalogging information.

Learn the basics →

Stay Updated

Sign up to receive the latest rotary engine resources and tuning guides.

ⓕ ⓣ ⓘ ⓤ

Get in Touch

Sealing the FD3S hatch and hood to prevent water entry

The FD3S hatch forms part of a larger weather system with the bonnet, windscreen cowl, side glass and door apertures. A failed seal lets wind-driven rain enter the cabin, while a blocked drain can make an otherwise sound car leak. Perished EPDM rubber, torn lips, missing clips and a misaligned latch are common causes.

Water on the carpet does not always mean the hatch glass is leaking. Check the lower corners, quarter-window channels, rear bumper channels and windscreen plenum, as well as the door seals. A musty heater or air-conditioning smell after rain often points to damp carpet or an evaporator drain rather than a roof or windscreen failure.

Local conditions matter. Melbourne’s changeable rain leaves cars damp, Sydney’s salt-laden coastal air attacks clips and hinges, Brisbane’s summer storms arrive suddenly, and Perth’s dry months hide brittle rubber until a downpour. Australian-market FD3S cars are right-hand drive; parts listings here generally call the hood a bonnet and the rear luggage area a boot. Never use a flooded street to test an FD3S, because water near the low intake and rotary engine can cause serious damage.

Work from the outside inward: dry everything, reproduce the leak gently, inspect seals and sheet-metal channels, then clear the drainage paths. Replace damaged parts with the correct profile and keep the original clip locations. Household silicone can hide a symptom while trapping water or blocking a drain.

Trace the water path

Start with a dry cabin and a controlled hose test. Open and securely support the bonnet, inspect the cowl and wiper-pivot area, and watch the hatch’s lower corners during short bursts of water. The hatch and glass should shed water, not direct it into the boot.

Trace each channel with thin paper or a clean towel instead of assuming the wettest point is the source. Rain from above points towards the hatch seal and upper glass; wind-driven entry can involve side seals or door apertures. Alarm wiring, amplifiers and trim can also hide a leak path.

For combined body and cabin work, check that seat or luggage changes do not foul the hatch aperture or retain water. This rear-seat comfort update shows why interior packaging matters when a child seat, dog barrier or touring load shares the boot.

Inspect the bonnet and hatch seals

The bonnet—still called the hood in overseas catalogues—seals against the cowl and surrounding panel. Look for continuous compression, glazing, cuts or flattened sections, then check hinge movement and latch alignment. Correct a high bonnet at the hinges or striker instead of forcing it down with sealant.

At the hatch, remove trim only if its retaining clips are intact. Inspect the seal’s lower corners, attachment channel and plastic drain outlets. A stretched seal may look neat but compress unevenly. Buy the current FD3S profile from a specialist or reputable Australian seller rather than forcing a generic push-in strip into the channel. Wreckers can help locate original trim clips, although their condition varies.

On a modified 13B, engine-bay and electrical changes can complicate diagnosis. The PowerFC setup guide helps explain aftermarket connections and whether a wet area belongs to an accessory rather than a body seal. Preserve the original loom routing and service access while investigating the bonnet seam.

Rebuild the weather boundary

Clean the cowl, hatch channels and drain outlets before fitting anything. Remove leaves and grit with a soft brush, flush with low-pressure water, and confirm each drain exits clear of the body. Replace brittle wiper boots, damaged clips and corroded screws together. For repaired panels, use automotive-grade seam sealer in the factory location and leave drains open.

Compare the likely causes and practical fixes across the main areas:

Area Common fault Best first check Durable repair
Bonnet-to-cowl seam Uneven compression or worn rubber Inspect hinge and latch alignment Correct alignment and renew the seal
Hatch lower corners Torn lip or blocked channel Dry-test and trace with paper Replace the seal and clear the drain
Side glass and quarter channels Missing clips or loose trim Check water path under pressure Renew clips, trim seals and channels
Windscreen cowl Leaves, dirt or split wiper boots Open the grille and inspect Clean, reseal and replace damaged boots

For factory diagrams, trim locations and VIN identification, use the TurboRX7 reference library before modifying a panel. Retain the original seal profile and make a small test fit before a full installation.

Test the repair in real conditions

After reassembly, let the interior dry overnight. Use a gentle hose, not a high-pressure washer aimed at the glass, and have one person watch inside while another applies water. Check sills, headlining, footwells and boot floor for damp patches. Repeat with the engine running and air-conditioning on fresh air, since airflow can reveal hidden leaks.

Test on a familiar road, but never deliberately flood the car. A short drive after a Melbourne shower, Sydney coastal run or Brisbane storm can reveal movement-related leaks. In Perth, inspect for dust packed into the cowl before winter rain. Record water conditions and the exact entry point so repeat testing is useful.

If the leak remains, photograph the wet area before removing trim and compare observations with experienced rotary owners. The Hogg76 technical resource can offer a second opinion on leak paths and sealing details. Treat community advice as a check against factory documentation, not a replacement for it.

Keep the FD3S ready for the next storm

Inspect weatherstrips every spring and after a severe storm. Wash dirt from the channels, renew torn clips, lubricate hinges and keep drains clear. Silicone dressing can reduce glazing on sound rubber but cannot restore a split or hardened seal. Check bonnet and hatch latch travel after any bump.

Power upgrades can add heat and airflow around the engine bay, so the bonnet and cowl need extra attention on a built car. The street-port tuning overview helps when checking intake and intercooler placement alongside cooling. Confirm water cannot reach a cold intake, electrical connector or ignition component, and that heat shielding does not cover a drain.

Before the next downpour, dry the FD3S, inspect both seals, clear every drain and repeat a low-pressure test. Save the factory diagrams, record what you find, and correct the first weak point instead of layering sealant over several. A methodical seal-and-drain inspection is the quickest route to a dry cabin and dependable weekend use.